electrical basic safety presentation training

Editor's Notes

• #1 This presentation is designed to assist trainers conducting OSHA 10-hour General Industry outreach training for workers. Since workers are the target audience, this presentation emphasizes hazard identification, avoidance, and control – not standards. No attempt has been made to treat the topic exhaustively. It is essential that trainers tailor their presentations to the needs and understanding of their audience. This presentation is not a substitute for any of the provisions of the Occupational Safety and Health Act of 1970 or for any standards issued by the U.S. Department of Labor. Mention of trade names, commercial products, or organizations does not imply endorsement by the U.S. Department of Labor.
• #2 This module addresses OSHA’s General Industry electrical standards contained in 29 CFR 1910 Subpart S. OSHA also has electrical standards for construction and maritime, but recommends that employers in these industries follow the general industry electrical standards whenever possible for hazards that are not addressed by their industry-specific standards. Suitability of electrical equipment for an identified purpose may be evidenced by listing or labeling by a nationally recognized testing laboratory which makes periodic inspections of equipment production and states that such equipment meets nationally recognized standards or tests to determine safe use in a specified manner. The Lockout/Tagout (LOTO) standard, 29 CFR 1910.147, is not covered in this presentation. However, you can find information on the Lockout-Tagout Interactive Training Program, under “OSHA Advisors” on the OSHA web site, www.osha.gov. Electricity is one of the most common causes of fire in homes and workplaces. Explosions have also resulted from electrical sources.
• #3 Operating an electric switch is like turning on a water faucet. Behind the faucet or switch there must be a source of water or electricity with something to transport it, and with a force to make it flow. In the case of water, the source is a reservoir or pumping station; the transportation is through pipes; and the force to make it flow is provided by a pump. For electricity, the source is the power generating station; current travels through electric conductors (wires); and the force to make it flow - voltage, measured in volts, is provided by a generator. Resistance - Dry skin has a fairly high resistance, but when moist, resistance drops radically, making it a ready conductor. - Measured in ohms. Use extra caution when working with electricity when water is present in the environment or on the skin. Pure water is a poor conductor, but small amounts of impurities, such as salt and acid (both are contained in perspiration), make it a ready conductor.
• #4 A small current that passes through the trunk of the body (heart and lungs) is capable of causing severe injury or electrocution. Low voltages can be extremely dangerous because, all other factors being equal, the degree of injury increases the longer the body is in contact with the circuit.
• #6 Grounding is a physical connection to the earth, which is at zero volts. Electricity travels in closed circuits, and its normal route is through a conductor. Electric shock occurs when the body becomes a part of the circuit. Electric shock normally occurs in one of three ways - when an individual is in contact with the ground and contacts: 1. Both wires of an electric circuit, or 2. One wire of an energized circuit and the ground, or 3. A metallic part that has become energized by contact with an energized conductor. The metal parts of electric tools and machines may become energized if there is a break in the insulation of the tool or machine wiring. A worker using these tools and machines is made less vulnerable to electric shock when there is a low-resistance path from the metallic case of the tool or machine to the ground. This is done through the use of an equipment grounding conductor—a low-resistance wire that causes the unwanted current to pass directly to the ground, thereby greatly reducing the amount of current passing through the body of the person in contact with the tool or machine.
• #7 Contact with both energized wires of a 240-volt cable will deliver a shock. This type of shock can occur because one live wire may be at +120 volts while the other is at –120 volts during an alternating current cycle, which is a potential difference of 240 volts.
• #10 Note that wire-gauge size is inversely related to the diameter of the wire. For example, a No. 12 flexible cord has a larger diameter wire than a No. 14 flexible cord.
• #11 If the circuit breakers or fuses are too big (high current rating) for the wires they are supposed to protect, an overload in the circuit will not be detected and the current will not be shut off. A circuit with improper overcurrent protection devices – or one with no overcurrent protection devices at all – is a hazard.
• #12 The basic idea of an overcurrent device is to make a weak link in the circuit. In the case of a fuse, the fuse is destroyed before another part of the system is destroyed. In the case of a circuit breaker, a set of contacts opens the circuit. Unlike a fuse, a circuit breaker can be re-used by re-closing the contacts. Fuses and circuit breakers are designed to protect equipment and facilities, and in so doing, they also provide considerable protection against shock in most situations. However, the only electrical protective device whose sole purpose is to protect people is the ground-fault circuit-interrupter.
• #13 The GFCI continually matches the amount of current going to an electrical device against the amount of current returning from the device along the electrical path. Whenever the amount of current going differs from the amount returning by approximately 5 milliamperes, the GFCI interrupts the electric power within as little as 1/40 of a second, protecting you from a dangerous shock. GFCI’s are able to detect the loss of current resulting from leakage through a person who is beginning to be shocked. If this situation occurs, the GFCI switches off the current in the circuit. GFCI’s are different from circuit breakers and fuses because they detect leakage currents rather than overloads.
• #14 Grounding is a physical connection to the earth, which is at zero volts. Current flows through a conductor if there is a difference in voltage (electrical force). If metal parts of an electrical wiring system are at zero volts relative to ground, no current will flow if our body completes the circuit between these parts and ground. Two kinds of grounds are required by the standard: 1. Service or system ground. In this instance, one wire — called the neutral conductor or grounded conductor — is grounded. In an ordinary low-voltage circuit, the white (or gray) wire is grounded at the generator or transformer and again at the service entrance of the building. This type of ground is primarily designed to protect machines, tools, and insulation against damage. 2. For enhanced worker protection, an additional ground, called the equipment ground, must be furnished by providing another path from the tool or machine through which the current can flow to the ground. This additional ground safeguards the electric equipment operator if a malfunction causes the metal frame of the tool to become energized.
• #15 Overhead power lines must be deenergized and grounded by the owner or operator of the lines, or other protective measures must be provided before work is started. Protective measures (such as guarding or insulating the lines) must be designed to prevent contact with the lines. Minimum clearance distances for employees working in the vicinity of overhead power lines are given in 29 CFR 1910.333(c)(3). PPE may consist of rubber insulating gloves, hoods, sleeves, matting, blankets, line hose, and industrial protective helmets.
• #16 Electrical accidents appear to be caused by a combination of three factors: 1. Unsafe equipment and/or installation, 2. Workplaces made unsafe by the environment, and 3. Unsafe work practices. There are various ways of protecting people from the hazards caused by electricity. These include: insulation, guarding, grounding, electrical protective devices, and safe work practices.
• #17 1910.304(f)(4)
• #18 1910.304(f)(5)(v)(C)(3) Hazards of portable electric tools: Currents as small as 10 mA can paralyze, or “freeze” muscles - Person cannot release tool - Tool is held even more tightly, resulting in longer exposure to shocking current Power drills use 30 times as much current as what will kill. Double-insulated equipment must be distinctly marked to indicate that the equipment utilizes an approved system of double insulation. The common marking is:
• #19 1910.303(g)(2)(i) 1910.303(g)(2)(iii)
• #20 1910.303(g)(2)(ii)
• #21 1910.305(b)(1) and (2)
• #22 1910.305(g)(1)(i) Other examples: Elevator cables Wiring of cranes and hoists Prevention of the transmission of noise or vibration Appliances where the fastening means and mechanical connections are designed to permit removal for maintenance and repair Data processing cables approved as part of the data processing system
• #24 1910.305(g)(1)(iii)
• #26 OSHA’s electrical safety-related work practice requirements are contained in 29 CFR 1910.331-.335. Deenergizing Electrical Equipment. The accidental or unexpected sudden starting of electrical equipment can cause severe injury or death. Before ANY inspections or repairs are made the current must be turned off at the switch box and the switch padlocked in the OFF position. At the same time, the switch or controls of the machine or other equipment being locked out of service must be securely tagged to show which equipment or circuits are being worked on. For more information on the Lockout/Tagout (LOTO) standard, 1910.147, see the Lockout/Tagout Interactive Training Program at the osha web site, www.osha.gov and find this reference under “OSHA Advisors”.