Capitulo 3, 7ma edición

Capitulo 3, 7ma edición

• 1.
  CHAPTER 3 3.1. Anempty metal paint can is placed on a marble table, the lid is removed, and both parts are discharged (honorably) by touching them to ground. An insulating nylon thread is glued to the center of the lid, and a penny, a nickel, and a dime are glued to the thread so that they are not touching each other. The penny is given a charge of +5 nC, and the nickel and dime are discharged. The assembly is lowered into the can so that the coins hang clear of all walls, and the lid is secured. The outside of the can is again touched momentarily to ground. The device is carefully disassembled with insulating gloves and tools. a) What charges are found on each of the five metallic pieces? All coins were insulated during the entire procedure, so they will retain their original charges: Penny: +5 nC; nickel: 0; dime: 0. The penny’s charge will have induced an equal and opposite negative charge (-5 nC) on the inside wall of the can and lid. This left a charge layer of +5 nC on the outside surface which was neutralized by the ground connection. Therefore, the can retained a net charge of −5 nC after disassembly. b) If the penny had been given a charge of +5 nC, the dime a charge of −2 nC, and the nickel a charge of −1 nC, what would the final charge arrangement have been? Again, since the coins are insulated, they retain their original charges. The charge induced on the inside wall of the can and lid is equal to negative the sum of the coin charges, or −2 nC. This is the charge that the can/lid contraption retains after grounding and disassembly. 3.2. A point charge of 20 nC is located at (4,-1,3), and a uniform line charge of -25 nC/m is lies along the intersection of the planes x = −4 and z = 6. a) Calculate D at (3,-1,0): The total flux density at the desired point is D(3, −1, 0) = 20 × 10−9 4π(1 + 9) −ax − 3 az √ 1 + 9 point charge − 25 × 10−9 2π √ 49 + 36 7 ax − 6 az √ 49 + 36 line charge = −0.38 ax + 0.13 az nC/m2 b) How much electric flux leaves the surface of a sphere of radius 5, centered at the origin? This will be equivalent to how much charge lies within the sphere. First the point charge is at distance from the origin given by Rp = √ 16 + 1 + 9 = 5.1, and so it is outside. Second, the nearest point on the line charge to the origin is at distance R = √ 16 + 36 = 7.2, and so the entire line charge is also outside the sphere. Answer: zero. c) Repeat part b if the radius of the sphere is 10. First, from part b, the point charge will now lie inside. Second, the length of line charge that lies inside the sphere will be given by 2y0, where y0 satisfies the equation, 16 + y2 0 + 36 = 10. Solve to find y0 = 6.93, or 2y0 = 13.86. The total charge within the sphere (and the net outward flux) is now Φ = Qencl = [20 − (25 × 13.86)] = −326 nC . 27
• 2.
  3.3. The cylindricalsurface ρ = 8 cm contains the surface charge density, ρs = 5e−20|z| nC/m2 . a) What is the total amount of charge present? We integrate over the surface to find: Q = 2 ∞ 0 2π 0 5e−20z (.08)dφ dz nC = 20π(.08) −1 20 e−20z ∞ 0 = 0.25 nC b) How much flux leaves the surface ρ = 8 cm, 1 cm < z < 5cm, 30◦ < φ < 90◦ ? We just integrate the charge density on that surface to find the flux that leaves it. Φ = Q = .05 .01 90◦ 30◦ 5e−20z (.08) dφ dz nC = 90 − 30 360 2π(5)(.08) −1 20 e−20z .05 .01 = 9.45 × 10−3 nC = 9.45 pC 3.4. In cylindrical coordinates, let D = (ρaρ + zaz)/ 4π(ρ2 + z2 )1.5 . Determine the total flux leaving: a) the infinitely-long cylindrical surface ρ = 7: We use Φa = D · dS = ∞ −∞ 2π 0 ρ0 aρ + z az 4π(ρ2 0 + z2)3/2 · aρ ρ0 dφ dz = ρ2 0 ∞ 0 dz (ρ2 0 + z2)3/2 = z ρ2 0 + z2 ∞ 0 = 1 where ρ0 = 7 (immaterial in this case). b) the finite cylinder, ρ = 7, |z| ≤ 10: The total flux through the cylindrical surface and the two end caps are, in this order: Φb = z0 −z0 2π 0 ρ0 aρ · aρ 4π(ρ2 0 + z2)3/2 ρ0 dφ dz + 2π 0 ρ0 0 z0 az · az 4π(ρ2 + z2 0)3/2 ρ dρ dφ + 2π 0 ρ0 0 −z0 az · −az 4π(ρ2 + z2 0)3/2 ρ dρ dφ where ρ0 = 7 and z0 = 10. Simplifying, this becomes Φb = ρ2 0 z0 0 dz (ρ2 0 + z2)3/2 + z0 ρ0 0 ρ dρ (ρ2 + z2 0)3/2 = z ρ2 0 + z2 z0 0 − z0 ρ2 + z2 0 ρ0 0 = z0 ρ2 0 + z2 0 + 1 − z0 ρ2 0 + z2 0 = 1 where again, the actual values of ρ0 and z0 (7 and 10) did not matter. 3.5. Let D = 4xyax + 2(x2 + z2 )ay + 4yzaz C/m2 and evaluate surface integrals to find the total charge enclosed in the rectangular parallelepiped 0 < x < 2, 0 < y < 3, 0 < z < 5 m: Of the 6 surfaces to consider, only 2 will contribute to the net outward flux. Why? First consider the planes at y = 0 and 3. The y component of D will penetrate those surfaces, but will be inward at y = 0 and outward at y = 3, while having the same magnitude in both cases. These fluxes 28
• 3.
  will thus cancel.At the x = 0 plane, Dx = 0 and at the z = 0 plane, Dz = 0, so there will be no flux contributions from these surfaces. This leaves the 2 remaining surfaces at x = 2 and z = 5. The net outward flux becomes: Φ = 5 0 3 0 D x=2 · ax dy dz + 3 0 2 0 D z=5 · az dx dy = 5 3 0 4(2)y dy + 2 3 0 4(5)y dy = 360 C 3.6. In free space, volume charge of constant density ρv = ρ0 exists within the region −∞ < x < ∞, −∞ < y < ∞, and −d/2 < z < d/2. Find D and E everywhere. From the symmetry of the configuration, we surmise that the field will be everywhere z-directed, and will be uniform with x and y at fixed z. For finding the field inside the charge, an appropriate Gaussian surface will be that which encloses a rectangular region defined by −1 < x < 1, −1 < y < 1, and |z| < d/2. The outward flux from this surface will be limited to that through the two parallel surfaces at ±z: Φin = D · dS = 2 1 −1 1 −1 Dz dxdy = Qencl = z −z 1 −1 1 −1 ρ0 dxdydz where the factor of 2 in the second integral account for the equal fluxes through the two surfaces. The above readily simplifies, as both Dz and ρ0 are constants, leading to Din = ρ0z az C/m2 (|z| < d/2), and therefore Ein = (ρ0z/ 0) az V/m (|z| < d/2). Outside the charge, the Gaussian surface is the same, except that the parallel boundaries at ±z occur at |z| > d/2. As a result, the calculation is nearly the same as before, with the only change being the limits on the total charge integral: Φout = D · dS = 2 1 −1 1 −1 Dz dxdy = Qencl = d/2 −d/2 1 −1 1 −1 ρ0 dxdydz Solve for Dz to find the constant values: Dout = (ρ0d/2) az (z > d/2) −(ρ0d/2) az (z < d/2) C/m2 and Eout = (ρ0d/2 0) az (z > d/2) −(ρ0d/2 0) az (z < d/2) V/m 3.7. Volume charge density is located in free space as ρv = 2e−1000r nC/m3 for 0 < r < 1 mm, and ρv = 0 elsewhere. a) Find the total charge enclosed by the spherical surface r = 1 mm: To find the charge we integrate: Q = 2π 0 π 0 .001 0 2e−1000r r2 sin θ dr dθ dφ Integration over the angles gives a factor of 4π. The radial integration we evaluate using tables; we obtain Q = 8π −r2 e−1000r 1000 .001 0 + 2 1000 e−1000r (1000)2 (−1000r − 1) .001 0 = 4.0 × 10−9 nC 29
• 4.
  b) By usingGauss’s law, calculate the value of Dr on the surface r = 1 mm: The gaussian surface is a spherical shell of radius 1 mm. The enclosed charge is the result of part a. We thus write 4πr2 Dr = Q, or Dr = Q 4πr2 = 4.0 × 10−9 4π(.001)2 = 3.2 × 10−4 nC/m2 3.8. Use Gauss’s law in integral form to show that an inverse distance field in spherical coordinates, D = Aar/r, where A is a constant, requires every spherical shell of 1 m thickness to contain 4πA coulombs of charge. Does this indicate a continuous charge distribution? If so, find the charge density variation with r. The net outward flux of this field through a spherical surface of radius r is Φ = D · dS = 2π 0 π 0 A r ar · ar r2 sin θ dθ dφ = 4πAr = Qencl We see from this that with every increase in r by one m, the enclosed charge increases by 4πA (done). It is evident that the charge density is continuous, and we can find the density indirectly by constructing the integral for the enclosed charge, in which we already found the latter from Gauss’s law: Qencl = 4πAr = 2π 0 π 0 r 0 ρ(r ) (r )2 sin θ dr dθ dφ = 4π r 0 ρ(r ) (r )2 dr To obtain the correct enclosed charge, the integrand must be ρ(r) = A/r2 . 3.9. A uniform volume charge density of 80 µC/m3 is present throughout the region 8 mm < r < 10 mm. Let ρv = 0 for 0 < r < 8 mm. a) Find the total charge inside the spherical surface r = 10 mm: This will be Q = 2π 0 π 0 .010 .008 (80 × 10−6 )r2 sin θ dr dθ dφ = 4π × (80 × 10−6 ) r3 3 .010 .008 = 1.64 × 10−10 C = 164 pC b) Find Dr at r = 10 mm: Using a spherical gaussian surface at r = 10, Gauss’ law is written as 4πr2 Dr = Q = 164 × 10−12 , or Dr(10 mm) = 164 × 10−12 4π(.01)2 = 1.30 × 10−7 C/m2 = 130 nC/m2 c) If there is no charge for r > 10 mm, find Dr at r = 20 mm: This will be the same computation as in part b, except the gaussian surface now lies at 20 mm. Thus Dr(20 mm) = 164 × 10−12 4π(.02)2 = 3.25 × 10−8 C/m2 = 32.5 nC/m2 3.10. Volume charge density varies in spherical coordinates as ρv = (ρ0 sin πr)/r2 , where ρ0 is a constant. Find the surfaces on which D = 0. 30
• 5.
  3.11. In cylindricalcoordinates, let ρv = 0 for ρ < 1 mm, ρv = 2 sin(2000πρ) nC/m3 for 1 mm < ρ < 1.5 mm, and ρv = 0 for ρ > 1.5 mm. Find D everywhere: Since the charge varies only with radius, and is in the form of a cylinder, symmetry tells us that the flux density will be radially-directed and will be constant over a cylindrical surface of a fixed radius. Gauss’ law applied to such a surface of unit length in z gives: a) for ρ < 1 mm, Dρ = 0, since no charge is enclosed by a cylindrical surface whose radius lies within this range. b) for 1 mm < ρ < 1.5 mm, we have 2πρDρ = 2π ρ .001 2 × 10−9 sin(2000πρ )ρ dρ = 4π × 10−9 1 (2000π)2 sin(2000πρ) − ρ 2000π cos(2000πρ) ρ .001 or finally, Dρ = 10−15 2π2ρ sin(2000πρ) + 2π 1 − 103 ρ cos(2000πρ) C/m2 (1 mm < ρ < 1.5 mm) 31
• 6.
  3.11. (continued) c) forρ > 1.5 mm, the gaussian cylinder now lies at radius ρ outside the charge distribution, so the integral that evaluates the enclosed charge now includes the entire charge distri- bution. To accomplish this, we change the upper limit of the integral of part b from ρ to 1.5 mm, finally obtaining: Dρ = 2.5 × 10−15 πρ C/m2 (ρ > 1.5 mm) 3.12. The sun radiates a total power of about 2 × 1026 watts (W). If we imagine the sun’s surface to be marked off in latitude and longitude and assume uniform radiation, (a) what power is radiated by the region lying between latitude 50◦ N and 60◦ N and longitude 12◦ W and 27◦ W? (b) What is the power density on a spherical surface 93,000,000 miles from the sun in W/m2 ? 3.13. Spherical surfaces at r = 2, 4, and 6 m carry uniform surface charge densities of 20 nC/m2 , −4 nC/m2 , and ρs0, respectively. a) Find D at r = 1, 3 and 5 m: Noting that the charges are spherically-symmetric, we ascertain that D will be radially-directed and will vary only with radius. Thus, we apply Gauss’ law to spherical shells in the following regions: r < 2: Here, no charge is enclosed, and so Dr = 0. 2 < r < 4 : 4πr2 Dr = 4π(2)2 (20 × 10−9 ) ⇒ Dr = 80 × 10−9 r2 C/m2 So Dr(r = 3) = 8.9 × 10−9 C/m2 . 4 < r < 6 : 4πr2 Dr = 4π(2)2 (20 × 10−9 ) + 4π(4)2 (−4 × 10−9 ) ⇒ Dr = 16 × 10−9 r2 So Dr(r = 5) = 6.4 × 10−10 C/m2 . b) Determine ρs0 such that D = 0 at r = 7 m. Since fields will decrease as 1/r2 , the question could be re-phrased to ask for ρs0 such that D = 0 at all points where r > 6 m. In this region, the total field will be Dr(r > 6) = 16 × 10−9 r2 + ρs0(6)2 r2 Requiring this to be zero, we find ρs0 = −(4/9) × 10−9 C/m2 . 3.14. The sun radiates a total power of about 2 × 1026 watts (W). If we imagine the sun’s surface to be marked off in latitude and longitude and assume uniform radiation, (a) what power is radiated by the region lying between latitude 50◦ N and 60◦ N and longitude 12◦ W and 27◦ W? (b) What is the power density on a spherical surface 93,000,000 miles from the sun in W/m2 ? 3.15. Volume charge density is located as follows: ρv = 0 for ρ < 1 mm and for ρ > 2 mm, ρv = 4ρ µC/m3 for 1 < ρ < 2 mm. 32
• 7.
  a) Calculate thetotal charge in the region 0 < ρ < ρ1, 0 < z < L, where 1 < ρ1 < 2 mm: We find Q = L 0 2π 0 ρ1 .001 4ρ ρ dρ dφ dz = 8πL 3 [ρ3 1 − 10−9 ] µC where ρ1 is in meters. b) Use Gauss’ law to determine Dρ at ρ = ρ1: Gauss’ law states that 2πρ1LDρ = Q, where Q is the result of part a. Thus Dρ(ρ1) = 4(ρ3 1 − 10−9 ) 3ρ1 µC/m2 where ρ1 is in meters. c) Evaluate Dρ at ρ = 0.8 mm, 1.6 mm, and 2.4 mm: At ρ = 0.8 mm, no charge is enclosed by a cylindrical gaussian surface of that radius, so Dρ(0.8mm) = 0. At ρ = 1.6 mm, we evaluate the part b result at ρ1 = 1.6 to obtain: Dρ(1.6mm) = 4[(.0016)3 − (.0010)3 ] 3(.0016) = 3.6 × 10−6 µC/m2 At ρ = 2.4, we evaluate the charge integral of part a from .001 to .002, and Gauss’ law is written as 2πρLDρ = 8πL 3 [(.002)2 − (.001)2 ] µC from which Dρ(2.4mm) = 3.9 × 10−6 µC/m2 . 3.16. In spherical coordinates, a volume charge density ρv = 10e−2r C/m3 is present. (a) Determine D. (b) Check your result of part a by evaluating ∇ · D. 3.17. A cube is defined by 1 < x, y, z < 1.2. If D = 2x2 yax + 3x2 y2 ay C/m2 : a) apply Gauss’ law to find the total flux leaving the closed surface of the cube. We call the surfaces at x = 1.2 and x = 1 the front and back surfaces respectively, those at y = 1.2 and y = 1 the right and left surfaces, and those at z = 1.2 and z = 1 the top and bottom surfaces. To evaluate the total charge, we integrate D · n over all six surfaces and sum the results. We note that there is no z component of D, so there will be no outward flux contributions from the top and bottom surfaces. The fluxes through the remaining four are Φ = Q = D · n da = 1.2 1 1.2 1 2(1.2)2 y dy dz front + 1.2 1 1.2 1 −2(1)2 y dy dz back + 1.2 1 1.2 1 −3x2 (1)2 dx dz left + 1.2 1 1.2 1 3x2 (1.2)2 dx dz right = 0.1028 C b) evaluate ∇ · D at the center of the cube: This is ∇ · D = 4xy + 6x2 y (1.1,1.1) = 4(1.1)2 + 6(1.1)3 = 12.83 33
• 8.
  c) Estimate thetotal charge enclosed within the cube by using Eq. (8): This is Q . = ∇ · D center × ∆v = 12.83 × (0.2)3 = 0.1026 Close! 3.18. State whether the divergence of the following vector fields is positive, negative, or zero: (a) the thermal energy flow in J/(m2 − s) at any point in a freezing ice cube; (b) the current density in A/m2 in a bus bar carrying direct current; (c) the mass flow rate in kg/(m2 − s) below the surface of water in a basin, in which the water is circulating clockwise as viewed from above. 3.19. A spherical surface of radius 3 mm is centered at P(4, 1, 5) in free space. Let D = xax C/m2 . Use the results of Sec. 3.4 to estimate the net electric flux leaving the spherical surface: We use Φ . = ∇ · D∆v, where in this case ∇ · D = (∂/∂x)x = 1 C/m3 . Thus Φ . = 4 3 π(.003)3 (1) = 1.13 × 10−7 C = 113 nC 3.20. Suppose that an electric flux density in cylindrical coordinates is of the form D = Dρ aρ. Describe the dependence of the charge density ρv on coordinates ρ, φ, and z if (a) Dρ = f(φ, z); (b) Dρ = (1/ρ)f(φ, z); (c) Dρ = f(ρ). 3.21. Calculate the divergence of D at the point specified if a) D = (1/z2 ) 10xyz ax + 5x2 z ay + (2z3 − 5x2 y) az at P(−2, 3, 5): We find ∇ · D = 10y z + 0 + 2 + 10x2 y z3 (−2,3,5) = 8.96 b) D = 5z2 aρ + 10ρz az at P(3, −45◦ , 5): In cylindrical coordinates, we have ∇ · D = 1 ρ ∂ ∂ρ (ρDρ) + 1 ρ ∂Dφ ∂φ + ∂Dz ∂z = 5z2 ρ + 10ρ (3,−45◦,5) = 71.67 c) D = 2r sin θ sin φ ar + r cos θ sin φ aθ + r cos φ aφ at P(3, 45◦ , −45◦ ): In spherical coordi- nates, we have ∇ · D = 1 r2 ∂ ∂r (r2 Dr) + 1 r sin θ ∂ ∂θ (sin θDθ) + 1 r sin θ ∂Dφ ∂φ = 6 sin θ sin φ + cos 2θ sin φ sin θ − sin φ sin θ (3,45◦,−45◦) = −2 3.22. (a) A flux density field is given as F1 = 5az. Evaluate the outward flux of F1 through the hemispherical surface, r = a, 0 < θ < π/2, 0 < φ < 2π. (b) What simple observation would have saved a lot of work in part a? (c) Now suppose the field is given by F2 = 5zaz. Using the appropriate surface integrals, evaluate the net outward flux of F2 through the closed surface consisting of the hemisphere of part a and its circular base in the xy plane. (d) Repeat part c by using the divergence theorem and an appropriate volume integral. 34
• 9.
  3.23. a) Apoint charge Q lies at the origin. Show that div D is zero everywhere except at the origin. For a point charge at the origin we know that D = Q/(4πr2 ) ar. Using the formula for divergence in spherical coordinates (see problem 3.21 solution), we find in this case that ∇ · D = 1 r2 d dr r2 Q 4πr2 = 0 The above is true provided r > 0. When r = 0, we have a singularity in D, so its divergence is not defined. b) Replace the point charge with a uniform volume charge density ρv0 for 0 < r < a. Relate ρv0 to Q and a so that the total charge is the same. Find div D everywhere: To achieve the same net charge, we require that (4/3)πa3 ρv0 = Q, so ρv0 = 3Q/(4πa3 ) C/m3 . Gauss’ law tells us that inside the charged sphere 4πr2 Dr = 4 3 πr3 ρv0 = Qr3 a3 Thus Dr = Qr 4πa3 C/m2 and ∇ · D = 1 r2 d dr Qr3 4πa3 = 3Q 4πa3 as expected. Outside the charged sphere, D = Q/(4πr2 ) ar as before, and the divergence is zero. 3.24. (a) A uniform line charge density ρL lies along the z axis. Show that ∇ · D = 0 everywhere except on the line charge. (b) Replace the line charge with a uniform volume charge density ρ0 for 0 < ρ < a. Relate ρ0 to ρL so that the charge per unit length is the same. Then find ∇ · D everywhere. 3.25. Within the spherical shell, 3 < r < 4 m, the electric flux density is given as D = 5(r − 3)3 ar C/m2 a) What is the volume charge density at r = 4? In this case we have ρv = ∇ · D = 1 r2 d dr (r2 Dr) = 5 r (r − 3)2 (5r − 6) C/m3 which we evaluate at r = 4 to find ρv(r = 4) = 17.50 C/m3 . b) What is the electric flux density at r = 4? Substitute r = 4 into the given expression to find D(4) = 5 ar C/m2 c) How much electric flux leaves the sphere r = 4? Using the result of part b, this will be Φ = 4π(4)2 (5) = 320π C d) How much charge is contained within the sphere, r = 4? From Gauss’ law, this will be the same as the outward flux, or again, Q = 320π C. 3.26. If we have a perfect gas of mass density ρm kg/m3 , and assign a velocity U m/s to each differential element, then the mass flow rate is ρmU kg/(m2 − s). Physical reasoning then 35
• 10.
  leads to thecontinuity equation, ∇ · (ρmU) = −∂ρm/∂t. (a) Explain in words the physical interpretation of this equation. (b) Show that s ρmU · dS = −dM/dt, where M is the total mass of the gas within the constant closed surface, S, and explain the physical significance of the equation. 3.27. Let D = 5.00r2 ar mC/m2 for r ≤ 0.08 m and D = 0.205 ar/r2 µC/m2 for r ≥ 0.08 m (note error in problem statement). a) Find ρv for r = 0.06 m: This radius lies within the first region, and so ρv = ∇ · D = 1 r2 d dr (r2 Dr) = 1 r2 d dr (5.00r4 ) = 20r mC/m3 which when evaluated at r = 0.06 yields ρv(r = .06) = 1.20 mC/m3 . b) Find ρv for r = 0.1 m: This is in the region where the second field expression is valid. The 1/r2 dependence of this field yields a zero divergence (shown in Problem 3.23), and so the volume charge density is zero at 0.1 m. c) What surface charge density could be located at r = 0.08 m to cause D = 0 for r > 0.08 m? The total surface charge should be equal and opposite to the total volume charge. The latter is Q = 2π 0 π 0 .08 0 20r(mC/m3 ) r2 sin θ dr dθ dφ = 2.57 × 10−3 mC = 2.57 µC So now ρs = − 2.57 4π(.08)2 = −32 µC/m2 3.28. Repeat Problem 3.8, but use ∇ · D = ρv and take an appropriate volume integral. 3.29. In the region of free space that includes the volume 2 < x, y, z < 3, D = 2 z2 (yz ax + xz ay − 2xy az) C/m2 a) Evaluate the volume integral side of the divergence theorem for the volume defined above: In cartesian, we find ∇ · D = 8xy/z3 . The volume integral side is now vol ∇ · D dv = 3 2 3 2 3 2 8xy z3 dxdydz = (9 − 4)(9 − 4) 1 4 − 1 9 = 3.47 C b. Evaluate the surface integral side for the corresponding closed surface: We call the surfaces at x = 3 and x = 2 the front and back surfaces respectively, those at y = 3 and y = 2 the right and left surfaces, and those at z = 3 and z = 2 the top and bottom surfaces. To evaluate the surface integral side, we integrate D · n over all six surfaces and sum the results. Note that since the x component of D does not vary with x, the outward fluxes from the front and back surfaces will cancel each other. The same is true for the left 36
• 11.
  and right surfaces,since Dy does not vary with y. This leaves only the top and bottom surfaces, where the fluxes are: D · dS = 3 2 3 2 −4xy 32 dxdy top − 3 2 3 2 −4xy 22 dxdy bottom = (9 − 4)(9 − 4) 1 4 − 1 9 = 3.47 C 3.30. Let D = 20ρ2 aρ C/m2 . (a) What is the volume charge density at the point P(0.5, 60◦ , 2)? (b) Use two different methods to find the amount of charge lying within the closed surface bounded by ρ = 3, 0 ≤ z ≤ 2. 3.31. Given the flux density D = 16 r cos(2θ) aθ C/m2 , use two different methods to find the total charge within the region 1 < r < 2 m, 1 < θ < 2 rad, 1 < φ < 2 rad: We use the divergence theorem and first evaluate the surface integral side. We are evaluating the net outward flux through a curvilinear “cube”, whose boundaries are defined by the specified ranges. The flux contributions will be only through the surfaces of constant θ, however, since D has only a θ component. On a constant-theta surface, the differential area is da = r sin θdrdφ, where θ is fixed at the surface location. Our flux integral becomes D · dS = − 2 1 2 1 16 r cos(2) r sin(1) drdφ θ=1 + 2 1 2 1 16 r cos(4) r sin(2) drdφ θ=2 = −16 [cos(2) sin(1) − cos(4) sin(2)] = −3.91 C We next evaluate the volume integral side of the divergence theorem, where in this case, ∇ · D = 1 r sin θ d dθ (sin θ Dθ) = 1 r sin θ d dθ 16 r cos 2θ sin θ = 16 r2 cos 2θ cos θ sin θ − 2 sin 2θ We now evaluate: vol ∇ · D dv = 2 1 2 1 2 1 16 r2 cos 2θ cos θ sin θ − 2 sin 2θ r2 sin θ drdθdφ The integral simplifies to 2 1 2 1 2 1 16[cos 2θ cos θ − 2 sin 2θ sin θ] drdθdφ = 8 2 1 [3 cos 3θ − cos θ] dθ = −3.91 C 37